Antec SOLO II Ficha de datos

S O L O I I USER MANUAL SILENCE RENEWED

10 2.2 MOTHERBOARD INSTALLATION Before proceeding: Check the manual for your CPU cooler to find out if there are steps you must do before installin

11 3. Screw your motherboard into the standoffs with the provided motherboard mounting screws. 2.3 INSTALLING THE KUHLER H2O The

12 2. The TrueQuiet™ fan has two small black clips attached to the fan’s two-speed switch. With your thumb and forefinger, spread the clips while pu

13 2. Remove the second screw with your other hand supporting the beam so the beam won’t drop. 3. Repeat steps 1 and 2 for the support beam screws a

14 2.5 CABLE MANAGEMENT There is a cable management area between the motherboard and right side panel as well as cable hooks located on the side

15 2. Attach the drive rails to your 5.25” device. These rails have three depth settings that accommodate the depth of your 5.25” drive.

16 2.7 INTERNAL 3.5” AND 2.5” INSTALLATION (TRAY MOUNTS AND SUSPENSION MOUNTING SYSTEM) The following text outlines the preparatory stages for

17 5. Insert the 3.5” / 2.5” drive into the drive cage by pinching the ends of the drive tray and sliding the tray along the rails until th

18 4. Twist the rear suspender and guide the hard drive through it. 5. Find the appropriate power connector on the PSU and connect it to the device

19 FRONT I/O PORTS SECTION 3

2 SOLO II USER’S MANUAL Congratulations on your purchase of the Antec SOLO II. The SOLO II emphasizes Quiet Computing™ and reinvents Antec’s renowne

20 Pin SignalNames Pin SignalNames 1 USBPower1 2 USBPower2 3 NegativeSignal1 4 NegativeSignal2 5 PositiveSignal1 6 PositiveSignal2 7 Ground1 8 Ground2

21 Pin SignalNames (HDA) Pin SignalNames (AC’97) 1 MIC2L 1 MICIn 2 AGND 2 GND 3 MIC2R 3 MICPower 4 AVCC 4 NC 5 FRO-R 5 LineOut(R) 6 MIC2_JD 6 LineOut(

22 3.5 REWIRING MOTHERBOARD HEADER CONNECTIONS There may come a time when you need to reconfigure the pin-out of a motherboard header connector

23 COOLING SYSTEM SECTION 4

24 4.1 INCLUDED 120 MM TRUEQUIET™ REAR FAN The SOLO II comes with a 120 mm TrueQuiet™ rear fan. This fan has a two-speed switch that lets you choo

25 4.3 OPTIONAL FANS The SOLO II can accommodate two 120 mm front intake fans. The following shows you how to install one of thesefans using a 1

26 Antec, Inc. 47900 Fremont Blvd. Fremont, CA94538 tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam

3 TABLE OF CONTENTS SECTION 1: INTRODUCTION 1.1 Getting to Know your Chassis ...5 1.2

4 INTRODUCTION SECTION 1

5 1.1 GETTING TO KNOW YOUR CHASSIS 1. Internal: 3 x 3.5” / 2.5”using tray mount OR 2 x 3.5” with suspension mount cables 2.

6 1.2 CHASSIS SPECIFICATIONS Chassis Type Mid Tower Chassis Color Piano Black Dimensions 17.3” (H) x 8.1” (W) x 18.5” (D) 440 mm (H) x 205 mm (W)

7 1.4 BEFORE YOU BEGIN In order to ensure that your building experience with the SOLO II will be a positive one, please take note of the followi

8 HARDWARE INSTALLATION SECTION 2

9 2.1 SETTING UP Begin by removing the left side panel by loosening the thumbscrews and swinging the panel outward, pulling it back towards you;